25.5×25.5mm Happymodel CrazyF411 AIO F4 2-4S Flight Controller Built-in 20A BL_S ESC & Frsky Receiver for Toothpick RC Drone FPV Racing

$35 $62
25.5×25.5mm Happymodel CrazyF411 AIO F4 2-4S Flight Controller Built-in 20A BL_S ESC & Frsky Receiver for Toothpick RC Drone FPV Racing
25.5×25.5mm Happymodel CrazyF411 AIO F4 2-4S Flight Controller Built-in 20A BL_S ESC & Frsky Receiver for Toothpick RC Drone FPV Racing
$35 $62

🇺🇸 $35 / 🇪🇺 30€

 

COUPON PRICE: 🇺🇸 $35 / 🇪🇺 30€

25.5×25.5mm Happymodel CrazyF411 AIO F4 2-4S Flight Controller Built-in 20A BL_S ESC & Frsky Receiver for Toothpick RC Drone FPV Racing

*PLEASE NOTE for European Union VAT: Goods purchased with our COUPON and delivered to the destination located in the European Union (EU), VAT and duties (if applicable) have been included in their COUPON prices and there is no need to pay additional taxes.

Also for more:

– 25.5×25.5mm Offers see – HERE
– Toys Hobbies and Robot Coupons see – HERE
🇪🇺 EU Warehouse Coupons see – HERE
🇺🇸 USA Warehouse Coupons see – HERE

 

Join Our Telegram Channel

 

Brand Name: Happymodel
Model: CrazyF411 AIO
Item Name:  F4 Flight Controller Built-in 20A BL_S ESC & Frsky Receiver
Features:
– 25.5×25.5mm FC AIO ESC board for toothpick .
– Most powerful for whoop / toothpick style flight
– Supports 2-4s battery input and provides 20A to the motors. 
– Also Integrated SPI Frsky receiver working with D8/D16 protocols.
This integrated receiver has PA/LNA power amplifier and the diversity antenna.
This should give more control range for this flight controller.
Bind procedure:
Make the on board receiver get into bind mode: For 4.0.x version firmware Plug USB and then connect betaflight configurator and then move to CLI tab , type “bind_rx_spi” ,the Red LED on the top of the flight controller will getting to be solid , the onboard receiver is in bind mode; For 4.1.x or 4.2.x the bind code is “bind_rx”
Make your transmitter get into bind mode . If bind is successful the red led will starting to blink.   The red LED wouldn’t blinking when binding with some new ACCESS firmware frsky radio  , but the bind is actual successful , need to go to CLI command and type “save” to finish the binding .
SPI Receiver option:
Frsky_D compatible with Frsky D8 protocol
Frsky_X compatible with Frsky non-eu D16 protocol
Frsky_X_LBT compatible with Frsky EU-LBT D16 protocol (4.0.X or latest betaflight firmware support)
SFHSS compatible with Futaba S-FHSS protocol
Package Included:
1x F4 AIO ESC RX Board
1x Cable with Conenctor
1x bag of Screws & Standoffs

 

Specification:

F4 Flight ControllerMCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU-6000(SPI connection)
Board size: 28.5 * 28.5MM
Power supply: 2-4S battery input (DC 8V-17V)
Built-in 20A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Frsky D8/D16 SPI receiverBuilt-in 2.4G Power Amplification
Built-in Betaflight OSD(SPI Control)
Built-in Current meter
Built-in 5V 1.5A BEC
Built-in voltage detection
Firmware target: MATEKF411RX
Yaw Degrees should set to “-90 degree” to match the flight direction
Onboard 20A ESCMCU upgraded to EFM8BB21
Power supply: 2-4S LiPo/LiPo HV (7v/17v)
Current: 20A continuous peak 25A (5 seconds)
Support BLHeliSuite programmable
Factory firmware: F_H_40_REV16_7.HEX
Default protocol: DSHOT600
Internal Frsky NON-EU receiver Version SPI BUS receiver
Frsky D8/D16 compatibleCompatible Non EU transmitter both D8 mode and D16 mode
Channels: 8ch/16chDual antenna
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 400m

 

ID:1764273 – SKUG52809

1764273CN
Logo